|
1/2" x 2 1/4" x 6.5LFT Australian Cypress Reducer |
|
|
|
|
PRACYRED15 - 1/2" x 2 1/4" x 6.5LFT Australian Cypress Reducer Prefinished Reducers provide a smooth transition between floors of different heights. Perfect for connecting wood flooring with vinyl or low pile carpet. |
REVIEW SNAPSHOT®
by PowerReviews(based on 4 reviews)
Ratings Distribution
50%
of respondents would recommend this to a friend.
Reviewed by 4 customers
Sort by
Displaying reviews 1-4
Pros
Cons
Best Uses
Comments about 1/2" x 2 1/4" x 6.5LFT Australian Cypress Reducer:
used liquid nail and Super Bond to attach to tile
Pros
Cons
Best Uses
Comments about 1/2" x 2 1/4" x 6.5LFT Australian Cypress Reducer:
This product it to Brittle. You have to pre Drill the holes as big as the Nail or it will split but then there is no holding power of the nail
Pros
Cons
Best Uses
Comments about 1/2" x 2 1/4" x 6.5LFT Australian Cypress Reducer:
Beautiful wood. Much more challenging than 3/4 inch to install. I could not find a cleat or side nailer than did not shatter this 1/2 inch wood. I finally found a review recommending the use of a 1/2 -1/4 inch laminate stapler. This worked. I wish I was told this I would have just gone with the 3/4 inch.
Comments about 1/2" x 2 1/4" x 6.5LFT Australian Cypress Reducer:
The floor turned out beautifully! My friends can't believe the difference it made in our great room!
Bottom Line Yes, I would recommend this to a friend
Images shared by Jan
Images shared by Jan
Was this review helpful? Yes / No
- You may also flag this review
Displaying reviews 1-4
Do you have questions about this product?
AnswerBox - Get answers from Staff Experts and real customers by clicking "Ask a question"
or click here to ask our Customer Service Team
Q:
what type of wood flooring (laminate, engineered wood, etc.) is best when there is a midsize dog in the house?1 answer
A:
This product question would be better answered by our Sales Department, they are more familiar with all of our flooring products and can better assist you with your questions.Q:
I want to install this flooring over ceramic tile...would that be possible?1 answer
CUSTOMER CARE
A:
If the ceramic is flat, level, well secured, and sealer and contaminate free then you can fully glue 5/16" flooring to it. Follow glue-down instructions - www.lumberliquidators.com/assets/images/installation/schon.pdfQ:
someone told us we need to be careful what we use to clean our floor if it has a aluminum oxide finish. Is this true and if so what should I use?1 answer
A:
No "special cleaning instructions" for aluminum oxide finish needed.Q:
HOW DO YOU REPAIR A VERY SMALL DAMAGE TO THE FINISH OF THIS WOOD DONE BY A DROP OF SUPER GLUE THAT I WAS ABLE TO REMOVE .1 answer
A:
Thank you for writing in! I would be glad to help you with your questions.Q:
I want to lay this floor on concrete in the basement and then put a pool table on it. My basement is mainly above ground. Should I lay any subfloor down and is 7/16 TOO thin for this area?? Will it buckle in the future?1 answer
A:
You can find complete installation instructions on the product page by clicking on the specs tab and then clicking on - Installation Guide.pdf\nThank you for your question.Q:
Do you have insrallation instructions for this product. Schon Brazilian Walnut engineered.1 answer
A:
You can find complete installation instructions on the product page by clicking on the specs tab and then clicking on - Installation Guide.pdfQ:
I see the thickness of the board included, but what is the thickness of the veneer on this product?1 answer
CUSTOMER CARE
A:
On the low profile 5/16" the wear layer is 0.6mm plus 7 coats of Treffert or Klumpp (made in Germany) highly resistant polyurethane finish with aluminum oxide anti-scratch and a 55% gloss.Q:
I'm so frustrated with my vinyl floor I want to replace it with something I can safely and without damage use in my kitchen and laundry room. I'm on a slab, and I need to be able to pull the fridge out to clean behind with out ripping, tearing, denting, etc. Also, my mother lives with me and uses a rollator to get around, would this floor bear weight?1 answer
A:
Yes this should be able to handle the rollator walker but as far as the fridge being rolled out; that can damage any flooring. I would recommend using 6" x 4' strips of thin plywood (luan), masonite or wood paneling to roll the fridge onto and protect the flooring.Q:
Can this product be glued to a sheetrock wall to use as decorative wood?1 answer
A:
I don't believe it would stay adhered for long.Q:
Can you put a pool table on this floor?1 answer
CUSTOMER CARE
A:
Yes. Use floor protecters like caster cups or large felt pads to protect the floor.
