Lumber Liquidators logo
Flooring 101 Home Flooring Tools Manuals Norge 12V Drill and Multi-Tool Kit Manual

Norge 12V Drill and Multi-Tool Kit Manual






ITEM: 10023359


LI-ON DRILL/ MULTI KIT





WARNING!

Please read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS





GENERAL SAFETY RULES

Work Area

1.    Keep your work area clean and well lit. Cluttered benches and dark areas will invite accidents

2.    Do not operate power tools in explosive atmospheres such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes

3.    Keep bystanders, children, and visitors away while operating a power tool. Distraction can cause you to loose control.

ELECTRICAL SAFETY

1.    A battery operated tool with integral batteries or a separate battery pack must be recharged only with the specified charger for the battery. A charger that may be suitable for one type of battery may create a risk of fire when used with another battery.

2.    Use battery operated tool only with specifically designated battery pack. Use of any other batteries may create a risk of fire.

3.    Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.

4.    Do not expose power tools to rain or wet conditions.

PERSONAL SAFETY

1.    Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.

2.    Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts

3.    Avoid accidental starting. Be sure switch is in the locked or off position before inserting




battery pack. Carrying tools with your finger on the switch or inserting the battery pack into a tool with the switch on invites accidents.

4.    Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that is left attached to a rotating part of the tool may result in personal injury.

5.    Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enable better control of the tool in unexpected situations

6.    Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes, hard hat, or hearing protection must be used for appropriate conditions

7.    Do not wear loose clothing or jewelry. Contain long hair. Loose clothes, jewelry, or long hair can be drawn into air vents.

8.    Do not use on a ladder or unstable support. Stable footing on a solid surface enables better control of the tool in unexpected situations.

TOOL USE AND CARE

1.    Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control.

2.    Do not force tool. Use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is designed.

3.    Do not use tool if switch does not turn it on or off. A tool that cannot be controlled with the switch is dangerous and must be repaired.

4.    Disconnect battery pack from tool or place the switch in the locked or off position before making any adjustments, changing accessories, or storing the tool. Such preventive safety measures reduce the risk of starting the tool accidentally

5.    Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users

6.    When battery pack is not in use, keep it away from other metal objects like: paper clips, coins, keys, nails, screws, or other small metal objects that can make a connection




from one terminal to another. Shorting the battery terminals together may cause sparks, burns, or a fire.

7.    Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools with sharp cutting edges are less likely to bind and are easier to control.

8.    Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tools operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools.

9.    Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool may create a risk of injury when used on another tool.

10.    Keep the tool and its handle dry, clean and free from oil and grease. Always use a clean cloth when cleaning. Never use brake fluids, gasoline, petroleum-based products, or any strong solvents to clean your tool. Following this rule will reduce the risk of loss of control and deterioration of the enclosure plastic.

SERVICE

1.    Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel may result in a risk of injury.

2.    When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow maintenance instructions may create a risk of injury.

SPECIFIC SAFETY RULES

1.    Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring. Contact with a "live" wire will also make exposed metal parts of the tool "live" and shock the operator.

2.    Use a metal detector to determine if there are gas or water pipes hidden in the work area or call the local utility company for assistance before beginning the operation. Striking or cutting into a gas line will result in explosion. Water entering an electrical device may cause electrocution.




3.    Always hold the tool firmly with both hands for maximum control. Keep proper tooting and balance at all times.

4.    Keep hands away from cutting area. Do not reach under the material being cut.

5.    Do not use dull or damaged blades. Bent blade can break easily or cause kickback.

6.    Exercise extreme caution when handling the accessories. The accessories are very sharp.

7.    Wear protective gloves when changing cutting accessories. Accessories become hot after prolonged usage.

8.    Before scraping, check workpiece for nails. If there are nails, either remove them or set them well below intended finished surface. Striking a nail with accessory edge could cause the tool to jump.

9.    Do not wet sand with this tool. Liquids entering the motor housing is an electrical shock hazard. Never work in area which is soaked with a liquid, such as a solvent or water, or dampened such as newly applied wallpaper. There is an electrical shock hazard when working in such conditions with a power tool and heating of the liquid caused by scraping action may cause harmful vapors to be emitted from workpiece.

10.    Never aim the tool at people. Otherwise it may create serious personal injury.

11.    Know your power tool. Read operator's manual care-fully. Learn its applications and limitations, as well as the specific potential hazards related to this tool. Following this rule will reduce the risk of electric shock, fire, or serious injury.

12.    Always wear safety glasses with side shields. Everyday glasses have only impact resistant lenses. They are NOT safety glasses. Following this rule will reduce the risk of eye injury

13.    Protect your lungs. Wear a face or dust mask if the operation is dusty. Following this rule will reduce the risk of serious personal injury.

14.    Protect your hearing. Wear hearing protection during extended periods of operation. Following this rule will reduce the risk of serious personal injury.




15.    Use special precautions when sanding chemically pressure treated lumber, paint that may be lead based, or any other materials that may contain carcinogens. A suitable breathing respirator and protective clothing must be worn by all persons entering the work area. Work area should be sealed by plastic sheeting and persons not protected should be kept out until work area is thoroughly cleaned.

16.    Do not use sandpaper intended for larger sanding pads. Larger sandpaper will extend beyond the sanding pad causing snagging, tearing of the paper or kick-back. Extra paper extending beyond the sanding pad can also cause serious lacerations.

17.    Battery tools do not have to be plugged into an electrical outlet; therefore, they are always in operating condition. Be aware of possible hazards when not using your battery tool or when changing accessories. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

18.    Do not place battery tools or their batteries near fire or heat. This will reduce the risk of explosion and possibly injury.

19.    Never use a battery that has been dropped or received a sharp blow. A damaged battery is subject to explosion. Properly dispose of a dropped or damaged battery immediately.

20.    Batteries vent hydrogen gas and can explode in the presence of a source of ignition, such as a pilot light. To reduce the risk of serious personal injury, never use any cordless product in the presence of open flame. An exploded battery can propel debris and chemicals. If exposed, flush with water immediately.

21.    Do not charge battery tool in a damp or wet location. Following this rule will reduce the risk of electric shock.

22.    For best results, your battery tool should be charged in a location where the temperature is more than 50F but less than 100F. Do not store outside or in vehicles.

23.    Under extreme usage or temperature conditions, battery leakage may occur. If liquid comes in contact with your skin, wash immediately with soap and water, then neutralize with lemon juice or vinegar. If liquid gets into your eyes, flush them with clean water for at least 10 minutes, then seek immediate medical attention. Following




 this rule will reduce the risk of serious personal injury.

SAFETY RULES FOR CHARGER

WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow all

instructions listed below, may result in electric shock, fire and/or serious personal injury.

1.    Before using battery charger, read all instructions and cautionary markings in this manual, on battery charger, battery, and product using battery to prevent misuse of the products and possible injury or damage.

2.    Do not use charger outdoors or expose to wet or damp conditions. Water entering charger will increase the risk of electric shock.

3.    Use of an attachment not recommended or sold by the battery charger manufacturer may result in a risk of fire, electric shock, or injury to persons. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

4.    Do not abuse cord or charger. Never use the cord to carry the charger. Do not pull the charger cord rather than the plug when disconnecting from receptacle. Damage to the cord or charger could occur and create an electric shock hazard. Replace damaged cords immediately.

5.    Make sure cord is located so that it will not be stepped on, tripped over, come in contact with sharp edges or moving parts or otherwise subjected to damage or stress. This will reduce the risk of accidental falls, which could cause injury, and damage to the cord, which could result in electric shock.

6.    Keep cord and charger from heat to prevent damage to housing or internal parts.

7.    Do not let gasoline, oils, petroleum-based products, etc. come in contact with plastic parts. They contain chemicals that can damage, weaken, or destroy plastic.

8.    An extension cord should not be used unless absolutely necessary. Use of improper extension cord could result in a risk of fire and electric shock. If extension cord must be used, make sure:

       a. That pins on plug of extension cord are the same number, size and shape as those

of plug on charger.




       b. That extension cord is properly wired and in good electrical condition; and

       c. That wire size is large enough for AC ampere rating of charger as specified below:

Cord Length (Feet)  25'    50'    100'

Cord Size (AWG)    16    16    16

NOTE: AWG = American Wire Gauge

9.    Do not operate charger with a damaged cord or plug, which could cause shorting and electric shock. If damaged, have the charger replaced by an authorized serviceman.

10.    Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way. Take it to an authorized serviceman for electrical check to determine if the charger is in good working order.

11.    Do not disassemble charger. Take it to an authorized serviceman when service or repair is required. Incorrect reassembly may result in a risk of electric shock or fire.

12.    Unplug charger from outlet before attempting any maintenance or cleaning to reduce the risk of electric shock.

13.    Disconnect charger from the power supply when not in use. This will reduce the risk of electric shock or damage to the charger if metal items should fall into the opening. It also will help prevent damage to the charger during a power surge.

14.    Risk of electric shock. Do not touch uninsulated portion of output connector or uninsulated battery terminal.

15.    Save these instructions. Refer to them frequently and use them to instruct others who may use this tool. If you loan some one this tool, loan them these instructions also to prevent misuse of the product and possible injury

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

This manual contains important safety and operating instructions for battery charger HYCH3S1261500G.




1.    Before using battery charger, read all instructions and cautionary markings on battery charger, battery, and product using battery.

2.    To reduce the risk of injury, charge only MAGLITHION 12V lithium-ion battery packs. Other types of batteries may burst, causing personal injury or damage.

FEATURES

Please refer to fig. 1 to familiarize yourself with the major components of this tool before using it.

1.    Scraper

2.    Spindle

3.    On/Off Switch

4.    Battery Pack

5.    Charger

Please refer to fig.2 to familiarize yourself with the major components of this tool before using it.

1.    Key-less Chuck

2.    Torque Adjustment Ring

3.    Trigger Switch

4.    Forward/Reverse Switch

5.    Battery Pack

6.    Charger

ASSEMBLY

CAUTION! Always be sure that the tool is switched off before assembly, including insertion or removal of the battery pack.

Installing or removing battery pack




1.    To remove the battery pack, withdraw itfrom the tool while depressing the tabs on both sides of the battery pack.

2.    Toinsert the battery pack, align the ribs on the top of the battery with the grooves in the housing and slide it into place. Always insert it all the way until it locks in place with a little click. Lightly pull on the battery pack to ensure it is locked into place and will not accidentally fall out of the drill, causing an injury.

3.    Do not use force when inserting the battery pack. If the battery does not slide in easily, it is not being inserted correctly.

Installing and Removing Accessories

Before mounting any attachments, make sure battery pack is removed to avoid risk of accidental firing.

1.    To install accessories, loosen and remove the hex socket bolt on the spindle with the hex key provided. Mount the accessory onto the spindle and turn it to the desired angle and secure it with the hex socket bolt.

2.    To remove an accessory, loosen and remove the hex bolt on the spindle, then remove the accessory.

Installing Sanding Sheets

Your tool uses hook-and-loop backed sandpaper, which firmly grips the backing pad when applied with moderate pressure.

To change, merely peel off the old sandpaper, remove dust from the backing pad if necessary, and press the new sandpaper in place.

After considerable use the backing pad surface will become worn, and the backing pad must be replaced when it no longer offers a firm grip. If you are experiencing premature wear of the backing pad facing, decrease the amount of pressure you are applying during operation of the tool.

Note: when removing the backing pad, peel off the sanding sheet first to expose the hex socket bolt.




OPERATION

Switching On/Off

The tool is switched "ON" by the slide switch located on the topside of the motor housing

TO TURN THE TOOL "ON" slide the switch button forward to the end.

TO TURN THE TOOL "OFF" slide the switch button backward to the end.

Warning! Hold the tool with both hands while starting the tool, since torque from the motor can cause the tool to twist.

Application

Your tool is intended for sanding, sawing and separating wooden materials, plastic, plaster, non-ferrous metals and fasteners (e.g. nails and clamps) as well as for working on soft wall tiles and for dry sanding and scraping of small surfaces. It is especially suitable for working close to edges and for flush cutting.

OVERLOAD PROTECTION

The power cutter is fitted with an overload/overheat protection device. When the tool is forced to work at an excessive load, the protection device will be activated automatically to disconnect the power supply. If this occurs, switch off the tool and switch on again to resume the work, make sure to apply only suitable workload to the tool. When the tool works under heavy load for a long period of time, the temperature of the tool or battery pack will increase significantly. The protection device will be activated at a preset temperature to protect both the tool and the battery. If this occurs, switch off the tool and wait until it cools down to ambient temperature and resume work.

Note: when the voltage of battery pack is dropped to 7.5V, the protection device will also be activated. In this case, remove the battery pack and fully charge it before reuse.

ADDITIONAL PRECAUTIONS FOR CHARGER & BATTERY PACK

1. Do not charge battery pack when temperature is below 10C (50F) or above 40C (104F).




2.    Do not attempt to use a step-up transformer, an engine generator or DC power receptacle.

3.    Do not allow anything to cover or clog the charger vents.

4.    Always protect the batteryterminals when the battery pack is not used.

5.    Do not short the battery pack.

6.    Do not touch the terminals with any conductive material.

7.    Avoid storing battery cartridge in a container with other metal objectssuch as nails, coins, etc.

8.    Do not expose battery pack to water or rain.

Warning!

A battery short can cause a large current flow, overheating, possible burns and even a breakdown.

9.    Do not store the tool and Battery pack in locations where the temperature may reach or exceed 50C (122F).

10.    Do not incinerate the Battery pack even if it is severely damaged or is completely worn out. The battery pack can explode in a fire.

11.    Be careful not to drop, shake or strike battery.

12.    Do not charge inside a box or container of any kind. The battery must be placed in a well ventilated area during charging.

Charging With the Diagnostic Charger

Note: Newly purchased Batteries are not fully charged and must be charged before using in your cordless tool(s).

1.    Plug the battery charger into the proper AC voltage source.

2.    Insert the battery pack so that the ribs on the battery pack slide into the grooves on the battery charger. Insert the cartridge fully into the charger.




3.    When the battery pack is inserted, the Green charging light will flash indicating the charger has started the charging cycle. A steady Green light will indicate the battery is completely charged and should be removed from the charger.

4.    "A steady Red light after inserting the battery" indicates the battery is too warm or too cold to be charged. Once the battery has cooled, the Red light will go off and the flashing Green light will illuminate indicating the charge cycle has begun.

5.    "RED Light Flashing after inserting the battery" This indicates the battery pack is not properly inserted or the battery pack is defective and needs to be replaced. Please dispose of the defective battery in the prescribed method explained in this manual.

6.    After charging, unplug the charger from the power source.

7.    Other tips for extending Battery life: Do not store batteries completely discharged. Charge them fully before storing.

Important Battery Information: disposing the Battery pack

  • Your batteries are Lithium-Ion rechargeable batteries. Certain Local, State and Federal laws prohibit disposal of these batteries in ordinary trash.
  • Consult your local waste authorities for your disposal/recyclingoptions.

MAINTENANCE

Warning !

Preventive maintenance performed by unauthorized personnel may result in misplacing of internal wires and components which could cause serious hazard

CAUTION !

Always be sure that the tool is switched off and the battery pack is removed from the tool before attempting to perform inspection or maintenance

Regularly clean the tool's air vents with compressed dry air. Do not attempt to clean by inserting pointed objects through openings.

CAUTION!




Certain cleaning agents and solvents may damage plastic parts. Some of these are: gasoline, carbon tetrachloride, chlorinated cleaning solvents, ammonia and household detergents that contain ammonia.

ACCESSORIES

instruction manual-------------1pc

teethed cutting blade------------1pc

sanding base plate-------------1pc

Sandpaper-------------------1    pc

double-end driving bit---------------1pc

charger------------------------1pc

Hex key---------------------1    pc

SPECIFICATIONS

Model: 12V COMPACT MULTI-PURPOSE TOOL

Voltage: 12V-DC

No-load Speed: 17000 OPM

Model: 12V COMPACT DRILL/DRIVER

Rated Voltage: 12V-DC

No-load Speed: 0-500 RPM

Chuck Capacity: 10mm (3/8")

Torque Adjustment Settings: 24 Battery Type: 1300 mAh Li-ion Charger Input: 230-240VAC,50-60Hz,40W

Charger Output: 12VDC,1.5A


Flooring 101 Home Flooring Tools Manuals Norge 12V Drill and Multi-Tool Kit Manual